Steel Building Layout for a Two-Post Lift Home Shop
A man two counties over put up a 30 by 40 shop with a 14 foot eave because the kit salesman told him that was plenty for a lift. He was right about the lift. He was wrong about the truck on it.

A man two counties over put up a 30 by 40 shop with a 14 foot eave because the kit salesman told him that was plenty for a lift. He was right about the lift. He was wrong about the truck on it. The posts raised a crew cab until the roof sat four inches under a purlin, which meant he could never stand upright beside his own rear axle. He kept that building three years, sold it, and started again with an 18 foot eave.
I read permit applications for nine years, and the home shop with a lift is the project where the drawings and the owner's real plan drift apart the fastest. The plan set says storage. The reviewer approves a four inch slab on grade. Then a two post lift arrives in February and gets anchored into concrete that was never specified to hold it. Nothing tips over on the first day. That is exactly what makes it dangerous.
Add the clearance stack before you pick an eave height
Eave height is not the number you work from. The number you work from is the sum of four things, and people usually remember two of them.
Start with the overall column height of the lift. Most asymmetric two post lifts for home use stand 11 ft 6 in to 12 ft 2 in at the top of the column, and the overhead equalizer bar sits a few inches above that. Add the vehicle. A stock half ton crew cab is 6 ft 4 in to 6 ft 6 in tall. Then add the maximum rise, which on a 10,000 pound home lift is typically 69 to 72 inches at the lift pads. Finally add whatever the manufacturer wants between the top of the raised vehicle and the lowest obstruction, which is often 6 inches but sometimes nothing at all if you are willing to lift partway.
Run that for a real truck and you land near 17 feet before you count the purlin depth hanging below the rafter. This is why I tell people to write down the clear interior height they need and hand that number to the kit supplier instead of an eave figure. On a tapered rigid frame the haunch at the column can sit two to three feet lower than the ridge.
If you want one figure to remember: 18 feet of eave gets a full size pickup to the top of a standard lift with room to work under it. Sixteen feet works if you only service cars and small SUVs. Fourteen is a parking garage with extra steps.
The slab is where a reviewer stops reading
A two post lift puts its entire load into two small rectangles of concrete. The baseplate on a 10,000 pound lift is roughly 9 by 16 inches, and under load it is trying to pull the anchors out of the slab while prying the plate off the floor. That is a tension and shear problem, not a crushing problem, and it is why lift makers specify slab thickness and strength rather than just a floor.
The spec I see most often is 4 inches minimum of 3,000 psi concrete, cured at least 28 days, with the lift set on a flat area and anchors held back from control joints and slab edges. Several manufacturers raise that to 6 inches for the taller or higher capacity models. My advice is to pour 6 inches across the lift bay regardless, with a thickened pad and reinforcement where the columns land, because the cost difference across two bays is small and the retrofit is miserable. We go deeper into floor thickness in how thick a slab a steel building needs.
Anchors matter as much as thickness. Lift columns usually land on five or six wedge anchors each, commonly 3/4 inch diameter with about 3.5 to 4 inches of embedment, torqued to the value in the manual and not to feel. If the anchor spins before it reaches torque, the hole was drilled oversize or the concrete is soft, and the fix is a new location rather than a bigger wrench. Column anchors are a separate hardware family from the ones that hold the building down, which I covered in the piece on steel building anchor bolts.
Ask the concrete crew where the control joints will fall before they cut them. Lift columns and saw cut joints do not get along, and moving a joint on paper costs nothing.
The advice I disagree with
The standard line on forums is build it as tall as you can afford, you will never regret the height. I have watched that advice cost people the rest of their shop.
Eave height is one of the more expensive dimensions in a steel kit, because taller columns need heavier sections, bigger anchor bolts, more wall panel and more bracing, and the wind load on a tall sidewall grows faster than the height does. Every foot of eave above 16 also pushes the overhead door price up and often pushes the building out of the simple residential accessory path in local zoning, where height limits in the low 20s are common. On one application I reviewed, the owner traded a 60 foot length for a 24 foot eave, then discovered he had no room for a parts bench or a bathroom and no second bay to work in while a car sat in the air.
Depth and width buy you more usable shop than the last four feet of air. If the budget is fixed, I would take 18 feet of eave and 50 feet of length over 24 feet of eave and 36 feet of length every time. Height is for the vehicle. Floor is for you.
Bay width and the opening you forgot
A two post lift wants a bay about 14 feet wide for comfortable door swing on both sides of the car, and 16 feet if you want a toolbox against one wall. Anything under 12 feet and you will be climbing across the hood. Keep the lift at least 3 feet off the sidewall so the column has room and so you can walk the long side of the vehicle.
| What you service | Clear interior height | Lift bay width | Door opening |
|---|---|---|---|
| Cars and small crossovers | 15 ft | 14 ft | 10 by 10 ft |
| Half ton pickups and vans | 17 ft | 16 ft | 12 by 12 ft |
| Dually and lifted trucks | 19 ft | 18 ft | 12 by 14 ft |
| Dual lift bays with a bench wall | 17 ft | 32 ft total | two at 12 by 12 ft |
Note the door column. A 12 by 12 opening looks generous until a sectional door with tracks and a torsion spring assembly hangs inside the frame and takes 15 inches of headroom out of your clear height. A high lift track conversion or a jackshaft opener recovers some of it. The doors and openings guide runs through the trade-offs between sectional, roll-up and sliding hardware in a metal frame.
What the permit office will want to see
Nothing on this list is hard. It only becomes hard when it arrives after the slab is poured.
Tell the reviewer the lift is going in. Put it on the floor plan as a rectangle with a note, name the model, and attach the manufacturer's installation page that states the slab spec. In most offices that single page ends the conversation about floor thickness, because the reviewer now has a published requirement instead of your word. If the shop is attached to a dwelling or you plan to run a business out of it, expect questions about fire separation, floor drains and whether the use is still residential. A floor drain tied to anything that handles oil is an environmental matter in a lot of jurisdictions, and leaving it out is cheaper than arguing it through.
Electrical is the other one. A 10,000 pound lift usually runs on a 220 volt single phase circuit at 20 to 30 amps, and the power unit sits on the column, so the receptacle location is part of the layout rather than an afterthought.
My honest limit here is that I reviewed in one county, and height limits, accessory structure rules and slab inspection practice vary more than anything else in this trade. Call your plan desk and ask one question: does a vehicle lift in an accessory structure change the slab inspection for you. The answer takes two minutes and tells you which version of this project you are actually building. More layout write-ups sit in the use cases section.
FAQ
Can I put a two post lift on an existing 4 inch slab?
Often yes, if the concrete is sound, at least 3,000 psi, fully cured, and the model you bought lists 4 inches as acceptable. Core sampling is the honest way to find out thickness on an older pour. I have seen slabs sold as four inches measure two and a half at the middle.
How tall does the building need to be for a four post lift instead?
Less, usually. Four post lifts for storage raise a vehicle 6 to 7 feet and stack a second car underneath, so 14 to 15 feet of clear height covers most of them. They spread their load over four baseplates, which is also gentler on a thin slab.
Does adding a lift change my steel building insurance?
It can, particularly if a carrier reads the shop as commercial use. Tell them before, not after a claim. The premium change I have heard reported is modest, but a denied claim is not.
Should the lift bay slab be poured separately?
No. Pour it monolithic with the rest of the floor and thicken the section under the columns. A separate pour creates a cold joint right where the anchors want solid concrete.
More in Use Cases
Use Cases
Steel Building Dog Kennel Layout and Permit Rules
A woman in my old review district filed for a 40 by 60 steel building and wrote "storage" on the use line.
Use Cases
Steel RV Storage Building Sizes That Actually Fit
I have walked two jobs where the owner could not get the coach into the building we had just finished.
Use Cases
Steel Horse Barn Layout and What Your Horses Actually Need
A steel horse barn that looks perfect on the quote can still be a miserable place for a horse if the stalls, airflow and doors...